UHMWPE SEMI-PRODUCTS Ultra-high molecular weight polyethylene( UHMWPE )is an outstanding engineering plastic.It? characterized by the following properties.
FEATURESï¼Â (1)Very high abrasion resistance (2)Very high impact strength (3)Very low coefficient friction (4)Good self-lubricant (5)Excellent resistance to chemicals (6)Good resistance to low temperature. (7)Excellent dielectric properties
APPLICATIONSï¼Â âÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ
Abrasion Resistance and Self-lubricant : marine fender, truck liners, gearing wheels, bearing bushes, sliding elements, chute liners, bunker liners, chain wear strip, guide strips and liners. paper and cardboard Industry, suction blades, foil blades, scraper and deflecting blades etc. âÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ
Excellent Impact Strength : lug straps, picker stickers, loom pickers, picker shields and spinning etc. âÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ
Hygienically : food processing, slide guide mechanisms, cutting boards, rammers, rolling pins, chopping blocks and moulds etc. âÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ
High Resistance to Chemical Solvents: pump casings, seals, spray nozzles, agitator screws, acid pump impellers and valve liners, electroplating plating drums etc.
UHMWPE SHEET Size 1030X2150mm ; 1200X2100mm ; 1000X3000mm 1500X3000mm ; 2000X3000mm ; 1000X4000mm Thickness 6.5~180mm
UHMWPE PIPES Size ODï¼ÂÂÂÂÂÂÂÂÂÂÂÂ32~630mm X IDï¼ÂÂÂÂÂÂÂÂÂÂÂÂ29~600mm Wall thickness 3.0~57.2mm
UHMWPE FILM Width (mm) 50,100~300 Length (meter/roll) 50~150 meter/roll Thickness (mm) 0.050/0.075/0.1/0.15 /0.2/0.3/?~1.5 Tolerance <0.5 mm thickness ±0.02~0.03 0.5~1.0mm thickness ±0.05~0.06 1.0~1.5mm thickness ±0.1~0.15 UHMWPE BAR Diameter (mm) 15 20 30 40 Roundness (mm) ≤3 ±1.5 ≤3 ±1.5 ≤3 ±1.5 ≤3 ±1.5 Length (mm) 1000 1000 1000 1000
Diameter (mm) 50 70 80 100 Roundness (mm) ≤5 ±2.5 ≤5 ±2.5 ≤5 ±2.5 ≤6 ±3 Length (mm) 1000 1000 1000 1000
Diameter (mm) 100 120 140 160 Roundness (mm) ≤6 ±3 ≤6 ±3 ≤6 ±3 ≤6 ±3 Length (mm) 1000 1000 1000 1000
Diameter (mm) 180 200 250 300 Roundness (mm) ≤6 ±3 ≤6 ±3 ≤6 ±3 ≤6 ±3 Length (mm) 150 150 150 150
Diameter (mm) 380 400 500 1000~2000 Roundness (mm) ≤6 ±3 ≤6 ±3 ≤6 ±3 ≤6 ±3 Length (mm) 150 150 150 150 Typical technical specification Density 0.935~0.980 gram/m3 Hardness 60~68 Water adsorption <0.01% Abrasion ratio 0.17 Friction coefficient 0.07~0.11 NOTCH impact strength 70 ~ 100 KJ/M2 IZOD Impact strength No break Tensile strength 30~35 Mpa Break elongation 200~300% ANTISTATIC UHMWPE Density 0.94~0.98g/cm3 Tensile strength 24 Mpa Elongation 140% Izod impact strength No break Hardness 60~68 Coefficient of linear thermal expansion 1/K:2X10-4 Surface resistivity 104 ~109 Ω-cm
High Abrasion Resistance UHMWPE Density 0.94~0.98g/cm3 Tensile strength 28 Mpa Elongation 160% Izod impact strength No break Hardness 60~68 Coefficient of linear thermal expansion 1/K 2X10-4 Abrasion loss-(dry abrasion) 0.003 g/cm2
UHMWPE-FRAS HA (Fire Retardant and Antistatic UHMWPE ) Density: GB1033 0.96~1.20 g/cm3 Crystalline Melting Range: 130 ~135 °C Impact Strength at Yield:GB 1043 >70KJ/m2 Elongation at break: GB1040 >60% Abrasion Index: g/cm2 GB/4085 0.011 Fire Behaviour: Oxygen Index:GB/2406 >28 % Volume Resistivity: M Ohm GB/1410 5X 105 Molecular weight:(ASTM 4020-81) 3.0 Million min
Low Friction UHMWPE Density 0.94~0.98g/cm3 Tensile strength 28 Mpa Elongation 160% Izod impact strength No break dynamic Friction Coefficient 0.07~0.11
|